Jump-N-Carry JNC660 Troubleshooting and FAQs: How to fix all the issues?

The Jump-N-Carry JNC660 is a great and reliable camera bag for anyone on the go. However, there are times when it can experience some minor problems. In this article, we will discuss some of the most common Jump-N-Carry JNC660 troubleshooting tips.

What battery is in a JNC660 jump starter?

Jump start your car with this easy-to-use jump starter. The JNC660 is compact and lightweight, perfect for taking with you on the go. It has a built-in battery and charges in just minutes. The battery in a JNC660 jump starter is a 12-volt, 6-amp hour battery. This is the perfect tool for restoring power to vehicles in an emergency.

Can a JNC660 jump starter charge a battery?

The answer to this question is yes, a JNC660 jump starter can charge a battery. Jump starters are designed to provide a quick burst of power to start a car. This power can be used to recharge a battery or power a device.

Jump starters are not designed to be used to charge batteries. The output of a jump starter is designed to provide a short burst of power, not to charge a battery. If you are trying to charge a battery using a jump starter, you may not get the results you are looking for.

If you are looking for a jump starter that can charge a battery, you may want to consider a model that has an integrated battery charger. This type of jump starter can charge batteries directly.

How many cold cranking amps does a JNC660 have?

The JNC660 is a small, lightweight engine that offers high performance and durability. It has a cold cranking amps rating of 660, which is higher than most other engines in its class. This means that the JNC660 can start cold more easily than other engines. Additionally, the JNC660 has a longer life expectancy than other engines, so you will not need to replace it as often.


What to do if the Jump-N-Carry will not hold a charge?

If you have a battery Load tester, load test the battery. First, charge the battery for 24 hours before applying the load test.

Connect your load tester to the Clore Automotive JNC660’s clamps to check bttery amperage. Depending on the model of load tester, your load testing procedure may vary, but a generic load test would bring the voltage down to 9.0 volts and result in an amp reading of 70 amps for 6 seconds.

Repeat this load test every 10 minutes for a total of three tests. If the amperage has dropped below 50 amps on the last test, suspect a bad or weak battery.

What was the Clore ideally designed for?

The Clore was designed for when vehicle’s an extra boost, due to a light or radio that was left on, or when a vehicle has not been started for a long time. The Clore will start most vehicles without the need of any other vehicle, but its main use is to provide an extra boost.

Will the Clore start every vehicle?

No it will not. If the battery is completely dead or if a car has other mechanical problems that prevents the Clore Automotive JNC660 may not be strong enough to start the vehicle.

How many jump starts can the Clore Automotive JNC660 deliver on a single charge?

Many factors play into this answer, including: How long of a time for each jump start, how low the original battery was, how long between jump starts, the temperature of the battery being jumped (cold temps. makes for difficult starting), the size of the engine (4-cycl, 6-cycl, 8-cycl, etc.), mechanical condition of the engine and the starter motor, and more.

These items must all be considered on an individual basis to accurately answer this question. It is possible to get 10-30 starts (although your results will differ) from a single charge, but you should still recharge the unit after every use.

What kind of accessories can be used in the 12 volt outlet?

Any accessory up to 12 amps can be plugged into the Clore JNC660. The unit is equipped with an automatic reset circuit breaker, should any device exceed 12 amps. Also note that this will limit any recharge current through the 12-volt outlet to 12 amps.

You can power most any 12-volt tool or accessory (examples: impact wrenches, fans, radios, cellular phones, navigation equipment, camcorders,  emergency power, trolling motors, coolers, small refrigerators, etc.)


What should I do if the JNC660 not working?

If the JNC660 not working, try the following troubleshooting steps:

  1. Check if the battery is fully charged. If the battery is not fully charged, the JNC660 may not work properly because of a low power supply.
  2. Make sure that the JNC660 is connected to a power source and switched on.
  3. Check whether there is any obstruction in the USB port of the JNC660. If there is an obstruction, it may cause problems with data transfer or communication between the JNC660 and your computer. Remove any obstructions and check again.
  4. Try different USB cables to see if there is a problem with your connection. Sometimes USB cables can be defective and cause issues with data communication between devices.

What should I do if the JNC660 not hold a charge?

There could be many reasons why a battery might not hold a charge, but some of the most common are as follows:

  • The battery could be defective.
  • The charging cable could be defective.
  • The battery could be overcharged.
  • The battery could be improperly installed.

If you are experiencing problems with your JNC660 holding a charge, there are a few things that you can do to troubleshoot the issue.

  1. First, make sure that the battery is properly installed in the device.
  2. Next, try charging the device using a different charging cable or power source.
  3. Finally, if all of these measures fail to resolve the issue, you may need to replace the battery.

What should I do if the JNC660 both lights flashing?

If the JNC660 both lights flashing, it could mean that the machine has detected a problem and is asking for your help. The most common problem that causes the JNC660 to both light up is a bad connection between the machine and the computer.

If your JNC660 is both flashing, it may be indicating a problem with the jump-N-carry system. To troubleshoot the issue, follow these steps:

  1. Make sure all cables are properly connected to the JNC660 and computer.
  2. Verify that all power cords are plugged into an outlet and turned on.
  3. Try to access the jump-N-carry system by pressing and holding down the ‘J’ key while powering on the JNC660 unit. If this does not work, try disconnecting any peripheral devices from the computer before trying to access the jump-N-carry system.
  4. If none of these steps solve the issue, your JNC 660 may need to be replaced.



If you encounter a series of problems or have doubts about the relevant information in the process of using JNC660 jump starters, you can read this article, in this article we cover many aspects, you can learn a lot. Finally, hope this article can really help you solve the problem.