The Guide to Fix Winplus jump starter Not Working or Go Beeping

In order to fix a Winplus jump starter that is not working or go beeping, you need to find different methods to solve different problems. Here are various conditions of your Winplus jump starter on your car and we list some causes and corresponding solutions. You can learn many useful information about this Winplus jump starter by reading this article. Come and read this fixing guide right now! 

Winplus jump starter Beeping: All the causes

Your Winplus jump starter beeping is likely caused by one of the following: a battery error, a low battery voltage, or an unauthorized connection. When you are experiencing this problem, please follow these steps to alleviate the symptoms:

Check the battery for proper polarity. Make sure positive (+) is positive and negative (-) is negative. If it isn’t, replace the battery. Check the jumpers on your jump starter for proper function. Make sure both jacks are connected in an alternating fashion and that power is flowing to both terminals. If power isn’t flowing to either terminal, your jump starter may not be working properly.

When the flashing lights or sound occurs on your Winplus jump Starter has flashing lights or sound, it may be defective and needs to be replaced. Yes, you could try to replace the battery in your jump starter, but it is usually cost-prohibitive to do so.

How to fix Winplus jump starter go beeping?

If your Winplus jump starter goes beeping every time it’s turned on, you may need to try and fix the issue. Here are some tips to help:

  1. Look for any signs of corrosion on the power cord. It means that the cord has been corroded and needs to be replaced if there is any brown or black liquid seeping from the connection, .
  2. Check the battery terminals. Those battery terminas need to be tightened up if they’re loose or if there’s any brown corrosion on them.
  3. Remove all of the insulation from around the power cords and plugs. This will make it easier to connect and disconnect cables when needed.
  4. Make sure that all of the components in your Winplus jump starter are in working order. 

Winplus jump starter

Winplus jump starter Not Working: All the causes

Potential causes of Winplus jump starter not working:

  • The battery may be too low. If your jump starter is not providing enough power, it may need to be replaced.
  • The jumper wire may have been damaged. If you can’t get the power to your jump starter, it might be able to fix itself by connecting the two ends of the jumper wire back together again.
  • The alternator may not be working properly and needs to be replaced. If your Winplus jump starter doesn’t turn on or has trouble starting, it might need to be checked out for an issue with the alternator.

How to fix Winplus jump starter not working?

To fix Winplus jump starter not working:

One is to try turning it off and on again, which may help start it up again. Another is to check the battery terminals and well as the power cord. If they’re corroded or have cracks, the jumper might not be able to connect properly. Finally, you could try reaching out to a repair professional if all of these measures make no sense and the jump starter still won’t turn on.

Winplus jump starter Not Holding A Charge: All the causes

Your Winplus jump starter is not holding a charge, the cause may be many. You could potentially have one of several causes based on how your WinplusJump starter has been used in the past. Here are some possible causes for not holding a charge on your Winplus jump starter:

  • Low voltage: If your Winplus jump starter has been run down to low voltage, it may not hold a charge anymore. This can be caused by either incorrect or careless use or by being in an unused position for too long. The best way to check this is to come into contact with the battery while it is still charging and see if there is any difference in voltage.
  • Physical damage: If your Winplus jump starter has been damaged in any way, including but not limited to fire, water, or vandalism, it may not hold a charge anymore.

How to fix Winplus jump starter not taking a charge?

Assuming you find your Winplus jump starter doesn’t take a charge, it may be because of a problem with the battery. Here are some steps to fix the issue:

  1. Check the charging port on your jump starter. If it’s not working, you’ll need to replace the battery.
  2. Clean the charging port if it’s dirty or covered in dust.
  3. Plug in your jump starter and make sure it’s connected to a power outlet. If everything looks good, you can start charging the battery by plugging it in and turning on the outlet.
  4. Wait for the jump Starter to charge until it’s fully charged before using it again.

Winplus jump starter

Winplus jump starter: Other Common Problems

Winplus jump starter: Doesn’t work after charging for two weeks

To solve the problem that your Winplus jump starter doesn’t work after charging for two weeks:

Making sure that the jump starter is properly plugged into a power outlet. If the jump starter is not plugged in, it will not be able to charge. Next, check the connections between the jump starter and the battery. Make sure that the connections are clean and secure.

Once the jump starter still doesn’t work, replace the battery is theb best choice. With a limited warranty and it is still valid, you can contact Winplus customer service to have the battery replaced. You may need to take it to a professional for further diagnosis if the jump starter is still not working after trying these steps.

Winplus jump starter: Doesn’t hold a charge for more than a few days

Many people are unaware that their Winplus jump starter doesn’t last very long. The powerful battery in the device only lasts for a few days, and many people are not happy with this fact. If you’re like most people, you would be interested in finding a way to get your Winplus jump starter to last longer.

There are a few ways to do this, but one of the easiest ways is to use a battery charger. After reading a lot of reviews, I conclude the batteries may have gone bad and called the company but no response. Any suggestions where I may find the batteries to replace and how to replace them would be much appreciated.

Winplus jump starter: Gets really hot when plugged in for charging

If you’re ever in need of a jump start or battery backup, the Winplus Jump Starter is the perfect option. It comes with a built-in battery that gets really hot when plugged in, so you can easily use it without having to risk damaging your device.

If you are looking for a car jump starter and a power bank in one, then the Winplus Car Jump Starter is for you. It is a very handy device that you can carry around in your pocket, your bag, or your car. Not only does it give life to your mobile devices and gadgets, but it can also bring your car back into life when it counts.

These days, the power bank is viewed by many as an essential part of their arsenal especially when they are always on the go. Winplus recognized this consumer need and stepped up their game by integrating a car jump starter into a power bank. People may not immediately think that something so small can actually start a car but the idea totally makes sense if you’re the type of person who always wants to have a ready solution for emergencies.

What you should attention when using a Winplus jump starter?

When using a Winplus jump starter, you should be careful to attention the following:

  • The jumper must fit snugly onto the battery
  • Make sure the cord is long enough to reach your vehicle’s dashboard
  • Avoid touching the negative terminal of the battery with your hand.

How to quickly and safely charge your Winplus jump starter?

Here are a few tips if you’re looking to quickly and easily charge your Winplus jump starter:

  1. Connect the power cord to your Winplus and plug it into an outlet.
  2. Aim the jump starter at the battery terminals in the Winplus and press the start button.
  3. Keep an eye on the countdown timer on your Winplus and wait until it’s finished counting down before trying to turn the jumper onto high power.

Your jump starter is one of the tools that you need to ensure are sharp and ready to go at a moment’s notice. When your car battery is weak or dead, a charged jump starter can mean the difference between getting back on the road quickly and waiting for hours for someone to come along to help – or spending money on a tow truck or other service vehicle.

Winplus jump starter


As far as we’re concerned, the jump starter not working or goes beeping, it is likely that something is wrong with the battery. It may be necessary to replace the battery if the problems persist!