This article discusses the Type S Jump Starter Quick Start Guide and all troubleshooting and works by using the Automotive Jump Starter and all troubleshooting. Model S Jump Starter made by Everstart, it is 6V/12V 500A peak, has heavy duty car battery clip 12ft power cord, red safety sign, DC jumper-free cable connector, T-connector, you can connect directly from A battery that draws power without being directly connected to other devices. It will be safer than normal jumper cables.
Having a reliable starter saves your car battery and keeps you safe on the road. But with all the different models of quickstarters, trying to figure out which one to choose can be confusing. So before making a decision, let me tell you everything you need to know about the Type S Jump Starter that made me buy it.
How to use Type S Jump Starter?
1. Charge the device using a USB cable and an adapter or computer. 2. Connect the jumper cables to the battery terminals of your car. 3. Turn off all electrical devices on your vehicle (e.g., lights, heater fan, radio, etc.) to reduce power consumption from the battery. 4. Press the power button for 3-5 seconds until you see a green light on the device turn on. The device is now ready to jump start your car. 5. Attach clamps of the jumper cables to the terminals of your car’s battery correctly: red clamp goes to “+” terminal and black clamp goes to “-” terminal (see picture). Make sure that clamps are firmly attached and do not touch each other or any metal parts of your vehicle. 6. Start your car’s engine, wait 10 seconds, then remove the clamps in reverse order (black clamp first and then red one). Store the device in a convenient location in your vehicle for emergency situations or bring it home and keep it charged so you can use it again when needed.
1. Ensure the Jump Starter is charged for a minimum of 12 hours before using for the first time. 2. Establish a safe working area and ensure the vehicle is in Park or Neutral, with the handbrake engaged, and that there are no leaks or sparks near the battery. 3. Connect the red clamp to the positive (+) terminal of the vehicle battery. 4. Connect the black clamp to the negative (-) terminal of the vehicle battery. 5. Start engine by turning key to on position (not start). Then start engine as usual. 6.Upon starting, remove clamps within 30 seconds to prevent discharge of Jump Starter, then turn off engine as you would normally do after starting your car (do not let engine idle). The unit may get warm during use but this is normal 7.For next jump start, repeat steps 1-6 above 8.After each jump starting, please place unit in a well ventilated area and allow to rest for at least 10 minutes.
Type S jump starter not charging
Plug the AC/DC adapter into a standard outlet and then plug the other end of the adapter into the jump starter. After you plug in your jump starter, it should start charging automatically. If it does not, please make sure that the device is plugged directly into an outlet–not a power strip or surge protector. It can take up to 24 hours to fully charge a dead battery. 2. Plug the included DC charger into the cigarette lighter adapter and then plug the other end into your vehicle’s cigarette lighter port. If your jump starter is plugged into a standard outlet, you can use this method to charge it while you are inside the car.
Keep in mind that charging times will be longer if you are driving around while charging. 3. Plug in your USB cable to charge your devices (optional). You can use your USB cable to charge Android devices like phones and tablets while they are connected to this jump starter. This can be used on iOS devices if you have purchased an additional Apple Lightning or 30-pin cable from us.
Use only the charger provided to charge your battery pack. Make sure that the switch is in the OFF position before plugging in the charger. Connect the adapter plug of the charger to the DC INPUT terminal of the jump starter unit. Plug the charger into a power outlet. The indicator light will turn on, indicating that it is charging normally. When charging is completed, it will turn green. The battery pack can be left connected to the charger for extended periods without damaging the batteries.
There are a few reasons why your jump starter may not be charging. Check the cable. The problem could be as simple as a faulty cable or connection. Make sure that the cables and connections are all plugged in correctly and there are no loose connections Manual power switch is off. On some models of jump starters, there is a manual on/off switch. Make sure that this switch is turned on to allow the unit to charge Battery is dead. If your jump starter has been unused for an extended period of time, it may no longer hold a charge. In this case, you must replace the battery pack.
The Everstart Maxx is also a good model.
Type s jump starter flashing green light
The Type S Jump Starter is the perfect companion for on-the-go power. The rechargeable lithium-ion battery is capable of jump starting 12V vehicles and powers a variety of devices. This guide will help you get started with your Type S Jump Starter. There is a lot that can be done with this device, so check out the videos and support articles for more information about all the features. Jump Starting a Vehicle Step 1: Ensure the vehicle to be jump started is turned off, then connect the positive (+) and negative (-) clamps to their corresponding terminals on the vehicle’s battery. Note: Avoid touching the clamp ends directly together as this may cause the unit to spark or short circuit, which may damage equipment or cause personal injury. Step 2: Press and hold the Power button on unit until it turns blue, then press and hold the Boost button on unit until it turns green. The Boost mode will automatically shut off after 5 seconds once your vehicle starts successfully. Note: The Type S Jump Starter also has an Emergency Light feature which can be turned on by pressing and holding the Power button on unit until it turns red.
Green LED Indicator Light is Flashing This indicates the jump starter is charging. The LED light will automatically turn off when the unit is fully charged. The Type S Jump Starter can be left plugged in for long periods of time because it is equipped with a smart circuit that prevents overcharging. LED indicator light does not come on when charger is plugged in First, ensure the USB cable is securely connected to the jump starter and to an AC wall outlet. If the LED indicator light does not illuminate, please contact this customer support team at 1-800-935-5040 Monday through Friday 9am – 5pm EST, or email us at [email protected]. Jump starter will not charge my device (laptop/tablet/smartphone) Ensure that you are using your own device cable to charge your electronics.
So you’ve just purchased the Jump Starter and are ready to get started. The Jump Starter is a very versatile tool that can be used in any situation you need it. From jump starting your vehicle to charging your phone, the Jump Starter is the essential tool for any car owner.
Before you start using the Jump Starter, make sure that it is charged by plugging in the charger that comes with it into the wall outlet and then connecting it to the jump starter inlet. Make sure that the power indicator light on the unit turns green. This may take over an hour for a full charge to complete. Once your unit is charged, we recommend that you keep it in your car so that if you ever need to use it for road side assistance or to charge something up, you will have it on hand at all times.
Why is my Type S jump starter flashing red?
If the LED light is flashing red, the unit may be too cold to use. Place in a warmer environment for at least 30 minutes. You may also be having issues with the battery. Please contact this customer service team at [email protected] so we can verify your product warranty and further assist you. Why won’t my Type S Jump Starter hold a charge? Your unit may have been exposed to extreme temperatures and stored improperly or it may be nearing the end of its life expectancy. If your unit is under warranty, please contact our customer service team at [email protected] so we can verify your product warranty and further assist you. Why won’t my Type S Jump Starter turn on? If your unit will not turn on, ensure that the battery connections are properly connected to the side terminals on your vehicle’s battery before attempting to charge your vehicle’s battery using the booster cables provided with this product.
The Type S Jump Starter is designed to protect the unit from damage. If you are having issues with the red light flashing, please see below for a list of potential issues and troubleshooting steps. The battery is not charged. Please charge using the supplied charger. The battery is defective. Please contact our customer service team for a replacement. Incorrect polarity protection: If the clamps were incorrectly attached to the vehicle battery then this may cause a red flashing light. Please make sure the clamps are correctly attached to the vehicle battery. Over-discharge protection: If you have left the jump starter connected to your vehicle battery for too long, this may cause a red light flashing on the jump starter. Please remove the jump starter as soon as possible and recharge it as soon as possible.
It won’t turn on Type S Jump Starter
The jump starter is not turned on: Press and hold the power button for 5 seconds until the LCD screen turns on. The jump starter is not charged: Connect the included charging cable directly to a wall outlet or into a 12V car lighter socket. Do not use a USB port on a computer or any other device to charge your jump starter. The unit will take about 6 hours to charge and the LCD screen will indicate when it’s fully charged. Note: A USB port can only provide 500 milliamps (0.5A) of power which is too weak for charging this device. The jump starter is not connected properly: Ensure that both battery clamps are connected to the battery terminals while they are touching each other (positive to positive, negative to negative). The jump starter is not properly grounded: Check that all of your vehicle’s doors, trunks and hoods are closed so that the jump starter can be grounded through its metal frame.
There are two main reasons that your Type S Jump Starter will not turn on:
1.The Clamps are not connected to the battery correctly 2.Faulty Jump Starter To see if the clamps are connected correctly, please follow these steps: 1. Remove the clamps from the jump starter; then plug in the AC wall charger and charge for 10-20 minutes (make sure you have a good connection to the wall outlet) 2. After charging, try turning on the unit by pressing and holding the power button for 5 seconds. 3.When you turn it on, check that there is a green light in each corner of the LCD screen (if there is not, please contact this customer service team at [email protected]). If your jump starter turns on with a green light in each corner of the LCD screen but won’t turn on once it’s unplugged, there is likely an electrical issue with your product and we will need to replace it under warranty. Please contact our customer service team at [email protected] to arrange a replacement.
The type S jump starter has a built in safety feature that will not allow it to turn on if the battery is low. The unit must be fully charged for it to work properly. To make sure that the unit is fully charged, plug the AC adapter into a wall outlet and attach it to the DC port on your Type S jump starter. You should see a red light turn on by the DC port when it is being charged. When the unit is fully charged, you will see a green light next to the DC port.
If you do not see any lights or if you are getting an error message with numbers on your screen, then your charger may not be working properly. Make sure that the AC adapter is plugged in correctly into both the wall and into your Type S jump starter. Also, make sure that there are no bent pins inside of either end of the AC adapter cable which could prevent it from charging correctly.
How to replace battery Type S Jump Starter?
The top of the jump starter has 3 LED lights. When the lights are green, the jump starter is ready to use. The red light will come on if the jump starter needs to be charged. How do I recharge my Type S? You can charge your Type S using the included AC or DC chargers. Plug the charger into a power source and connect it to your Type S. The red light on the top of your Type S will come on to let you know that it is charging. If you are charging via DC, please unplug your jumper cables from your vehicle before plugging in the charger. Once fully charged, the LED lights on top will turn green. This can take approximately two hours with AC and approximately six hours with DC current. My Type S is not responding – how do I fix this? If you start pressing buttons and nothing happens: First, check that the battery is charged (see above). Then, try holding down the power button for about 10 seconds until all three LEDs flash green once in a row. Now you should be able to operate again normally. If that does not work, see the next question below.
Before removing the battery, make sure you have a replacement battery of the same model to install. Some units may have a retaining strap on the back of the unit that will need to be removed. To remove and replace the battery, please follow these steps: Use a T15 Torx screwdriver to remove the screws in each corner of the unit. Once all four screws are removed, you can pry up on the tabs at each corner of the unit to separate it into two parts. With one hand holding each half of the unit, pull down on both halves until they separate completely.
1. Remove the battery from the jump starter case by sliding the red release latch and lifting up on the handle. 2. Remove the four screws holding the battery cover in place. 3. Remove the battery cover. 4. Remove all of the wires from both ends of the battery (the black wire is attached to two terminals). 5. Set the battery aside and purchase a replacement, if needed (12V, 4A/Hr) 6. Attach all of the wires (the black wire goes to two different terminals) to the new battery and replace the battery cover, securing it with four screws 7. Place the new battery back into its compartment in the case and slide the red latch to secure it in place.
Jump Starter will not hold a charge?
If you leave your unit plugged into the charger for an extended period of time, it will overcharge. If this happens, unplug the unit from the charger immediately. Overcharging can cause permanent damage to the unit. The LED indicator will flash red when the unit is overcharged. If this occurs, unplug the charger and allow the unit to drain until all of the lights are off. Do not attempt to jump start a vehicle while the indicator light is flashing. After fully draining your unit, plug it in to charge and make sure all of the lights stay on steadily. Jump Starter will not hold a charge? If you leave your unit plugged into the charger for an extended period of time, it will overcharge. If this happens, unplug the unit from the charger immediately. Overcharging can cause permanent damage to the unit. The LED indicator will flash red when the unit is overcharged. If this occurs, unplug the charger and allow the unit to drain until all of the lights are off. Do not attempt to jump start a vehicle while the indicator light is flashing. After fully draining your unit, plug it in to charge and make sure all of the lights stay on steadily.
How do I check the battery level on my jump starter?
The battery level indicator on the jump starter is located under the hood. Press the power button and the four LEDs will light up to indicate the current battery level. The more LEDs that light up, the better your charge. The jump starter has a safety feature that keeps it from powering on while it is charging. To verify that you are able to power on your jump starter, remove your jumper cables before attempting to power on your jump starter. My jump starter won’t hold a charge, how do I fix this? Please note: This will not work if you have a faulty battery or an issue with a component of your unit. Additionally, please ensure you are using quality, name brand chargers and cables with your unit for optimal results.
Summary:
The safety instructions and precautions are to prevent harm to you and others. If you follow the instructions, it should be safe. First, read all instructions before using your jump starter. Next, examine the jump starter carefully to make sure no breakage or damage has occurred while shipping. Inspect the outer surfaces, harnesses, clamps, case or anything else that may have been impacted by the shipping process.